DESIGN AND CONSTRUCTION OF AN INTELLIGENT 250 VOLTS BATTERY CHARGER WITH MICRO PROCESSOR USING SEVEN SEGMENT DISPLAY

  • Type: Project
  • Department: Engineering
  • Project ID: EGR0003
  • Access Fee: ₦5,000 ($14)
  • Chapters: 5 Chapters
  • Pages: 37 Pages
  • Format: Microsoft Word
  • Views: 1.3K
  • Report This work

For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Design And Construction Of An Intelligent 250 Volts Battery Charger With Micro Processor Using Seven Segment Display

 




TABLE OF CONTENTS

Title page                                             i

Certification page                                      ii

Dedication                                                 iii

Acknowledgement                                      iv

Abstract                                                    v

Table of content                                         vi-vii

CHAPTER ONE

Introduction                                             1

What is Battery Charger                             1

What is an Intelligent Battery Charger          1

Other Types of Battery Charger                   2-3

CHAPTER TWO

Literature Review                                      4-5

CHAPTER THREE

Component     Description                          6

Micro Controller                                        6-14

Resistor                                                   14-16

Transistor                                                16

Seven Segment Display                             17-18

Capacitor                                                        18-20

Transformer                                             21

Diode                                                      21-22

CHAPTER FOUR

Principle of Operation                                23-27

Circuit Diagram                                         28

Component List                                        29

CHAPTER FIVE

Conclusion                                               30

Recommendations                                    31

References                                               32


CHAPTER ONE.

INTRODUCTION

WHAT IS A BATTERY CHARGER: A battery charger is a device used to put energy into a secondary cell or rechargeable battery. By forcing on electric current through it.

The charge current depends upon the technology and capacity of the battery being charged. For example, the current that should be applied to recharge a 12v car battery will be very different from the current for a mobile phone battery.

WHAT IS AN INTELLIGENT BATTERY CHARGER: This is a battery charger whose output current depends upon the battery’s state. An intelligent charger may monitor  the battery’s voltage, temperature and/ or time under charge to determine the optimum charge current at that instant. Charging is terminated when a combination of the voltage, temperature and/or time indicates that the battery is fully charged.

OTHER TYPE OF BATTERY CHARGERS

1.   SIMPLE  BATTERY CHARGER: A simple charger works by connecting a constant dc power source to the battery being charged. A simple charger does not alter its output based on time or the charge on the battery. This simplicity means that a simple charger is inexpensive but there is a trade off in quality.

2.   TRICKLE BATTERY CHARGER:  A trickle charger is a kind of simple charger that charges the battery slowly, at the self-discharge rate. A trickle charger is the slowest kind of battery charger.

3.   TIMER-BASED BATTERY CHARGER: The output of timer charger is terminated after a predetermined time. Timer chargers were the most common type for high-capacity Ni-Cd cells in the late 1990s

4.   FAST BATTERY CHARGER: fast chargers make use of control circuitry in the batteries being charged to rapidly charge the batteries without damaging the cells element. Most such chargers have a cooling fan to help keep the temperature of the cells under control.

5.   PULSE BATTERY CHARGER: some charger use pulse technology in       which a pulse is fed to the battery. This DC pulse has a strictly controlled rise time, pulse width, pulse repetitive rate (frequency) and amplitude. This technology is used to work with any size, voltage, capacity or chemistry of batteries including automotive and valve-regulated batteries. .

6.   INDUCTIVE BATTERY CHARGER: Inductive battery chargers use electromagnetic induction to charge batteries. A charging station sends electromagnetic energy through inductive coupling to an electrical device which stores the energy in the batteries

7.      USB-BASED BATTERY CHARGER: Since the universal serial bus specification provides for a five-volt power supply, it is possible to use a USB cable as a power source for recharging batteries. 

DESIGN AND CONSTRUCTION OF AN INTELLIGENT 250 VOLTS BATTERY CHARGER WITH MICRO PROCESSOR USING SEVEN SEGMENT DISPLAY
For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Share This
  • Type: Project
  • Department: Engineering
  • Project ID: EGR0003
  • Access Fee: ₦5,000 ($14)
  • Chapters: 5 Chapters
  • Pages: 37 Pages
  • Format: Microsoft Word
  • Views: 1.3K

500
Leave a comment...

    Related Works

    ABSTRACT A battery charger is an electrical device employed for charging batteries.  This batteries that are usually charged by battery changer are the storage battery charger are the storage batteries also known as “accumulator” the battery changer changes.  The alternating current form the power line into d.c suitable for charging. When... Continue Reading
    ABSTRACT           A battery charger is an electrical device employed for charging batteries.  This batteries that are usually charged by battery changer are the storage battery charger are the storage batteries also known as “accumulator” the battery changer changes.  The alternating current form the power line into d.c suitable... Continue Reading
    ABSTRACT A battery charger is an electrical device employed for charging batteries. This batteries that are usually charged by battery changer are the storage battery charger are the storage batteries also known as “accumulator” the battery changer changes. The alternating... Continue Reading
    ABSTRACT This project presents the design and construction of a battery charger. A battery charger is an electrical/electronic device used to put energy into a secondary cell or rechargeable battery by forcing an electric current through it.  The system  consists of a step down transformer, an AC to DC converter and a DC voltage regulator. The... Continue Reading
    ABSTRACT The practical importance of a battery charging unit in today’s world cannot be over emphasized. This is so since these batteries or accumulators are immensely needed by automobiles and in science laboratories. This thesis describes the methodical approach to the design and construction of any battery changer. However the procedure... Continue Reading
    ABSTRACT This project which comprise of many chapters that deals extensively with designs and construction of battery charger with auto-cut off which is capable of charging a 12 volts battery. In this construction research, designs was carried out which historic research was used to break down and evaluate to a low level understating of what an... Continue Reading
                                                             ABSTRACT This project describes the design and construction of an automatic Battery charger. Automatic Battery chargers are not particularly cheap, but the protection they afford in protecting batteries against overcharging and possible battery damage is highly... Continue Reading
                                                             ABSTRACT This project describes the design and construction of an automatic Battery charger. Automatic Battery chargers are not particularly cheap, but the protection they afford in protecting batteries against overcharging and possible battery damage is highly... Continue Reading
      ABSTRACT         This project work describes the construction and designing of 12volt car battery charger with USB port for charging mobile phones. The charging process is focus more on 12volt lead car batteries commonly used in vehicles. This design was done by using I.C LM7812 and LM7806 with transformer of 230 volt and series of other... Continue Reading
    ABSTRACT   This project, 12v battery charge consist of few chapters, deal extensively with the design and construction of a batter charge which is capable of charging a 12v battery. The introductory chapter goes a long why in defining the battery charger and explanations of the mode of operations will be death with as we proceed.     TABLE OF... Continue Reading
    Call Us Get this work