CONSTRUCTION OF CAR TOUCH INTRUDER ALARM.

  • Type: Project
  • Department: Electrical Engineering
  • Project ID: ELE0004
  • Access Fee: ₦5,000 ($14)
  • Chapters: 6 Chapters
  • Pages: 70 Pages
  • Methodology: Scientific Method
  • Reference: YES
  • Format: Microsoft Word
  • Views: 7K
  • Report This work

For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

CONSTRUCTION OF CAR TOUCH INTRUDER ALARM
ABSTRACT

The main objective of this project was to ensure a proper security to car being parked in garage against theft or an intruder. The circuit uses three NE555 timers; one of the NE555 was wired as a monostable oscillator and remaining two were wired as tone generator and amplified to obtain a maximum audible sound. However, pin 2 of the first NE555 was used as sensor part .When pin 2 has contact with human body or hand it will activate the IC1 which will also bias transistor and this transistor was wired in a way that once it is powered it will close circuit thereby passing a negative supply voltage to tone generator circuit and outputted out through a loud speaker or buzzer.
This device functions as a major security device against car-theft as stated above. It is an electronic device that is connected to the battery of the car it is being installed in and gets activated when the car engine is switched off and the car stationed at a place. The device is not seen but, it has an indicator light which shows that the alarm has been activated. When the body of the car is touched by human hand, it sends a negative signal to the device which needs a negative pulse to get activated; it sends this negative from the human hand to the tone generator IC which triggers the alarm.    
                                          TABLE OF CONTENT
   CHAPTER ONE: Introduction                                                                               

   1.1    Background of study
1.2       Aims and objectives
    CHAPTER TWO: Literature Review
    CHAPTER THREE: Specification and operation of system component             

3.1       Description of NE55 Timer            
3.2       Description of Resistor
3.3       Description of Capacitor
3.4       Description of Diode
3.5       Description of Transformer
3.6       Description of Loud Speaker and Buzzer
3.7       Description of Transistor
3. 8     Description of L.E.D
    CHAPTER FOUR: Operation of system and its circuit and block diagram
4.1       Operation of  
4.2       The circuit diagram
4.3    The block diagram
    CHAPTER FIVE: Construction, Testing and Packaging
5.1    Values of components
5.2    Assembly
5.3    A schematic diagram of the finished work
    CHAPTER SIX: Conclusion and Recommendation
6.1       Conclusion
6.2       Recommendation
6.3       Observations
6.4       Dificulties
6.5      Reference                        
 CHAPTER ONE:  INTRODUCTION
1.1.            Background of the Study
        The first car alarm was a primitive contraption that utilized a bell or horn connected to the drive shaft. It was created by an unnamed Nebraska inventor in June 20th, 1920. It utilizes the drive shaft to operate its own bell or horn signal when the car is properly moved. This is just a little talk on a car alarm but not a car touch intruder alarm which is a modern, more advanced, and more reliable type of car alarm.
        This car touch sensitive alarm project consist of three NE555 timer IC, the first NE555 was wired as monostable  multi-vibrator and the remaining two were wired as tone generator. When the sensor is touch or has contact with human hand perhaps body, IC1 is triggered at its pin 2 and output pin 3 goes high for a time period previously set by the values of R4 (10M) and Q1 (transistor) was bias via R3 and this transistor is in such a way that once it was biased it will supply a negative voltage to tone generator thereby making two NE555 timer which was know as (tone generator) to oscillate to make a bell sound through the buzzer. The tone generators are configured as an astable multi-vibrator whose oscillation frequency can be varied with the help of PR1 and PR2. By adjusting the values of PR1 and PR2, modifications on the tone are possible.
The reset button is used to set or open circuit the system back to its initial stage. The system is powered with 12V power supply voltage.
The first chapter of this project is narrating on the introduction, the concept of the system and also the aims and objective. Chapter two is all about literature review. Chapter three talks about specification and operation of system component. Chapter four is operation of system. Chapter five is about construction, testing and packaging. Chapter six is conclusion, observation, recommendation and References.
1.2       AIM AND OBJECTIVE
       The main aim and objective of the design and construction this project is to create a comfort in the minds of vehicle owners or users when their vehicles are parked or stationed anywhere without much fear of car-theft.

CONSTRUCTION OF CAR TOUCH INTRUDER ALARM.
For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Share This
  • Type: Project
  • Department: Electrical Engineering
  • Project ID: ELE0004
  • Access Fee: ₦5,000 ($14)
  • Chapters: 6 Chapters
  • Pages: 70 Pages
  • Methodology: Scientific Method
  • Reference: YES
  • Format: Microsoft Word
  • Views: 7K

500
Leave a comment...

    Related Works

    CONSTRUCTION OF CAR TOUCH INTRUDER ALARM ABSTRACT The main objective of this project was to ensure a proper security to car being parked in garage against theft or an intruder. The circuit uses three NE555 timers; one of the NE555 was wired as a monostable oscillator and remaining two were wired as tone generator and amplified to obtain a maximum... Continue Reading
    ABSTRACT The intruder alarm system was designed and build in order to let the industrial and commercial company know how important alarm system is all about. These can be of Good help if the intruder will look through this project and support for the development of this project as to let the Federal Government know that the young engineering of... Continue Reading
    ABSTRACT The intruder alarm system was designed and build in order to let the industrial and commercial company know how important alarm system is all  about. These can be of Good help if the intruder will look through this project and support for the development of this project as to let the Federal Government know that the young engineering of... Continue Reading
    ABSTRACT The intruder alarm system was designed and build in order to let the industrial and commercial company know how important alarm system is all about. These can be of Good help if the intruder will look through this project and support for the development of this project as to let the Federal Government know that the young engineering of... Continue Reading
    ABSTRACT This project work deals on the Design and Construction of Intruder Detector Alarm System with Direction/Location Displaywhich is capable of detecting intrusion at any location, sound and alarm and display the exact location of the intruder using... Continue Reading
    CHAPTER ONE INTRODUCTION 1.1.          Background of the Study The industrial Electronics has changed the whole field of Engineering and technology is occurring so rapidly, even in developing countries. It is so because newer technologies overcome older ones. After the industrial revolution the world shifted towards the information... Continue Reading
    ABSTRACT A switch is an imperative constituent of any electronic or electrical circuit. It can either be mechanical, electro-mechanical or electronic. Mechanical and electro mechanical switches are prone to wear and tear with time. The introduction of semiconductors has led to the invention of electronic switches that are more efficient, fast and... Continue Reading
    ABSTRACT A switch is an imperative constituent of any electronic or electrical circuit. It can either be mechanical, electro-mechanical or electronic. Mechanical and electro mechanical switches are prone to wear and tear with time. The introduction of semiconductors has led to the invention of electronic switches that are more efficient, fast and... Continue Reading
    ABSTRACT This project deals on the design and construction of an intruder detector for home and office use. Security as one of the biggest issues in our world today and we need a system that will be able to monitor our home, offices and industries by using two sensing... Continue Reading
    ABSTRACT This work is a power supply monitoring device that triggers a buzzer when the mains supply cuts off. Thus a diode (bridge rectifier diode) was used to convert the AC voltage to DC voltage and the 240v/12v AC mains power transfer was used with a bridge rectifier for rectification and a 470Nf filter capacitor C1 for the smoothing of the... Continue Reading
    Call Us Get this work