GEAR DESIGN AND TYPES. (7D)

  • Type: Project
  • Department: Mechanical Engineering
  • Project ID: MCE0192
  • Access Fee: ₦5,000 ($14)
  • Pages: 20 Pages
  • Format: Microsoft Word
  • Views: 756
  • Report This work

For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853
INTRODUCTION
Each machine consists in principle of three basic parts: a motor or another prime mover (that sets the machine in motion), an actuating mechanism (which is directly doing the needed work:
digs a ditch, weaves cloth, peels potatoes, propels a ship, and so on), and a transmission that connects the first two parts. Sometimes, the transmission may be lacking, for example, in a fan the impeller is mounted  directly on the shaft of the electric motor. But in most cases, the transmission is indispensable, to
match the speed of the mover with that of the actuator, to set in motion several actuators from one
mover, or for another reason. For instance, on a big ship a steam turbine is usually used as a mover.
Its rotational speed is several thousands r/min, whereas the speed of the propeller (for better efficiency) should be about 100 r/min. Hence, between the turbine and the propeller shall be a
speed reducer.
On a small motor boat the propeller, with respect to the speed, may be mounted directly on
the shaft of the engine. But the engine is desired to be placed above the water (just to be maintained easily), and the propeller to work should be submerged; so in this case the transmission is needed as well.
A gear is the most common type of transmission; therefore, it is one of the mandatory  subjects when machine elements are discussed. The geometry of gears is well known, and it is not the subject of investigation here. But the analysis of strength and deformations in gears is impractical without some minimal presentation of tooth geometry. This is the theme of the following section. 

GEAR DESIGN AND TYPES. (7D)
For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Share This
  • Type: Project
  • Department: Mechanical Engineering
  • Project ID: MCE0192
  • Access Fee: ₦5,000 ($14)
  • Pages: 20 Pages
  • Format: Microsoft Word
  • Views: 756

500
Leave a comment...

    Related Works

    INTRODUCTION Each machine consists in principle of three basic parts: a motor or another prime mover (that sets the machine in motion), an actuating mechanism (which is directly doing the needed work: digs a ditch, weaves cloth, peels potatoes, propels a ship, and so on), and a transmission that connects the first two parts. Sometimes, the... Continue Reading
    INTRODUCTION Each machine consists in principle of three basic parts: a motor or another prime mover (that sets the machine in motion), an actuating mechanism (which is directly doing the needed work: digs a ditch, weaves cloth, peels potatoes, propels a ship, and so on), and a transmission that connects the first two parts. Sometimes, the... Continue Reading
    ABSTRACT This project work is concerned with assessment to different types of foundation and their mode of construction though looks like a literature review but entails full information and chosen. Foundation samples were limited to three different locations within Ilorin metropolis. Terzaghi equation was used for determining soil bearing... Continue Reading
    Table of Content Introduction   Objectives   Study design   Data collection   Results   Discussion   Recommendation   References Introduction Litter is the improper disposal of waste products through human activities (Berglund, Koivula & Eeva 2011). Why people litter?   Dropping litter where litter has already accumulated.   Lack of... Continue Reading
    ABSTRACT Soaps are the sodium salts or potassium salts of stearic acids or any other fatty acids. They are prepared by the saponification process, which is, reacting the oil which contain triglycerides with caustic soda (NaOH) to give the soap. However different oils... Continue Reading
    PREFACE This bibliography on information source of types of library in Nigeria, 2004 – 2010 was undertaken as a prerequisite for my graduation. It is aimed at providing student of library science on insight into the material/ resources publish in their field inside Nigeria. The title were collected from Books, Journals, Project, Theses, Bulletin... Continue Reading
    Title page . (A CASE STUDY OF THE FEDERAL UNIVERSITY OF AGRICULTURE UMUDIKE, ABIA STATE) CHAPTER ONE 1.0.    INTRODUCTION Crop production is an integral part of agriculture, the other half is animal production or husbandry. Crop production can either be on a... Continue Reading
    PREFACE This bibliography on information source of types of library in Nigeria, 2004 – 2010 was undertaken as a prerequisite for my graduation. It is aimed at providing student of library science on insight into the material/ resources publish in their field inside Nigeria. The title were collected from Books, Journals, Project, Theses, Bulletin... Continue Reading
    Overview: This project work was carried out to determine the effect of different spacing on the growth and yield of celosia argentea. The parameters considered for the experiment include plant height, leaf length, numbers of leaves and population of perforated leaves per plant, taken at 3, 5 and 7 weeks after planting. It was observed that the... Continue Reading
    Abstract The first part of this work established, with examples, the fact that there are more than one non-abelian isomorphic types of groups of order n = sp, (s,p) = 1, where s 1 was worked out and such groups have no non-abelian isomorphic types. This gave credence to the fact that a group of order 15 and its like do not have a non-abelian... Continue Reading
    Call Us Get this work