DESIGN AND CONSTRUCTION OF A COMPUTER BASED CONTROL OF ELECTRICAL APPLIANCES

  • Type: Project
  • Department: Electrical Engineering
  • Project ID: ELE0219
  • Access Fee: ₦5,000 ($14)
  • Pages: 63 Pages
  • Format: Microsoft Word
  • Views: 668
  • Report This work

For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853


INTRODUCTION

This project presents the design and construction of a computer based program used to control office appliance. It is based on a Graphic user interface (GUI) programming language (Visual Basic 6.0), Parallel Port Interactive Mode, Opto-Coupler Isolation of the computer from the appliance to prevent damage to the system should a fault develop in the appliance. The implementation was based on the interaction of the computer with electronic appliance via the 25 Pin Centronics Parallel Port Cable.





TABLE OF CONTENT





 





Title Page -      -      -      -      -      -      -      -      -      -      i





Dedication      -      -      -      -      -      -      -      -      -      ii





Acknowledgement  -      -      -      -      -      -      -      -      iii





Abstract  -      -      -      -      -      -      -      -      -      -      iv





List of Figures -      -      -      -      -      -      -      -      -      v





List of Table    -      -      -      -      -      -      -      -      -      vi





Table of Content     -      -      -      -      -      -      -      -      vii





 





CHAPTER ONE





INTRODUCTION





1.2 Objective of the Project -      -      -      -      -      -      1





1.3  Justification of the Project     -      -      -      -      -      2





1.4  The Scope of the Project -      -      -      -      -      -      2





1.5  Project Report Organization   -      -      -      -      -      3





 





CHAPTER TWO





REVIEW OF RELATED LITERATURE





2.3.1 The Hardware -      -      -      -      -      -      -      -      4





2.3.2  The Software       -      -      -      -      -      -      -      -      7





2.3.3  Parallel Port Basics      -      -      -      -      -      -      -      15





2.4 Opto-Electronic Component   -      -      -      -      -      28





2.5  The Relay -      -      -      -      -      -      -      -      -      34





CHAPTER THREE





METHODOLOGY





3.1  Design Approach    -      -      -      -      -      -      -      37





3.2  Software Development   -      -      -      -      -      -      37





3.2.1 Out Putting Data to the Parallel Port    -      -      -      38





3.2.2 Reading Data from the Parallel Port     -      -      -      40





 





CHAPTER FOUR





ANALYSIS AND DESIGN





CHAPTER FIVE





SYSTEM IMPLEMENTATION AND TESTING





5.1  Functional Test       -      -      -      -      -      -      -      -      51





 





CHAPTER SIX





 CONCLUSION AND RECOMMENDATION





5.1  Conclusion      -      -      -      -      -      -    &a

DESIGN AND CONSTRUCTION OF A COMPUTER BASED CONTROL OF ELECTRICAL APPLIANCES
For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Share This
  • Type: Project
  • Department: Electrical Engineering
  • Project ID: ELE0219
  • Access Fee: ₦5,000 ($14)
  • Pages: 63 Pages
  • Format: Microsoft Word
  • Views: 668

500
Leave a comment...

    Related Works

    Abstract In this project we designed a solar powered computer control system  for electrical machines and spark ignition engines. It is made up of a  hardware device that comprises of various electrical components  which are powered by a 25W solar panel. The power cord of the  machines are modified and connected to the hardware and the ... Continue Reading
    Abstract In this project we designed a solar powered computer control system  for electrical machines and spark ignition engines. It is made up of a  hardware device that comprises of various electrical components  which are powered by a 25W solar panel. The power cord of the  machines are modified and connected to the hardware and the ... Continue Reading
    ABSTRACT The purpose of this project is to design and construction of a central wireless switch for electrical and electronic appliances. A central wireless switch for electrical and electronic appliance is a GSM based online power control switch system that controls the entire appliance in the EEE general office using GSM network. It will act as... Continue Reading
    ABSTRACT This report is on stability study in electrical power system. The ability of an electric power system to reestablish the initial state (or one practically identical) after any disturbance manifested as a deviation from the initial parameter values for the system’s operation. The electric power sources in a power system are usually... Continue Reading
    ABSTRACT The need for a remote control system that can control domestic appliances and various lighting points and sockets has often been a concern for uses at times uses find it inconvenient and time they are leaving the house for work it has also often led to damage of appliances due to the fact that an appliances was not timed off before... Continue Reading
    CHAPTER ONE INTRODUCTION 1.1                             OBJECTIVE OF PROJECT The need for a remote control alert system that can control domestic appliances and various lighting points and sockets has often been a concern for users. At times users find it inconvenient and time consuming to go around turning their... Continue Reading
    ABSTRACT The need for a remote control system that can control domestic appliances and various lighting points and sockets has often been a concern for uses at times uses find it inconvenient and time they are leaving the house for work it has also often led to damage of appliances due to the fact that an appliances was not timed off before... Continue Reading
    ABSTRACT Whenever we think of redefined security, we think of coded electrical door lock. It is a microcontroller based security door lock that can be used in homes, offices, laboratories, etc. for more reliable and high fidelity door control system, powered by electrons panel or electromechanical panels. Due to high rate of insecurity, especially... Continue Reading
    ABSTRACT Whenever we think of redefined security, we think of coded electrical door lock. It is a microcontroller based security door lock that can be used in homes, offices, laboratories, etc. for more reliable and high fidelity door control system, powered by electrons panel or electromechanical panels. Due to high rate of insecurity, especially... Continue Reading
    ABSTRACT This project presents a 40A maximum power point tracking solar charge controller. The MPPT charge controller tries to keep the voltage and the power stable. The MPPT charge controller will harvest more power from the solar array – it will adjust its input voltage to harvest the maximum power from the solar array and then transform this... Continue Reading
    Call Us Get this work