12 VOLTS AUTOMATIC BATTERY CHARGING SYSTEM

  • Type: Project
  • Department: Electrical Engineering
  • Project ID: ELE0221
  • Access Fee: ₦5,000 ($14)
  • Pages: 56 Pages
  • Format: Microsoft Word
  • Views: 698
  • Report This work

For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853
ABSTRACT
This design is aimed at providing a system that has the capability of recharging batteries after use. The design is to incorporate an auto charging cut off circuit that operates when the battery is fully charged to avoid damaging the device and also a low voltage circuit which prevents the system from damage should in case the battery voltage level drops to a particular preset value.  This design is used to charge batteries not exceeding 36volts and a lineup of batteries not exceeding 10 in number. The current supply of the charging system does not exceed 3amp per charging time.


TABLE OF CONTENT

Title Page
Certification
Approval Page
Dedication
Acknowledgement
Abstract
TABLE OF CONTENT
CHAPTER ONE: INTRODUCTION
1.1    Background study
1.2    Aims and objectives
1.3    Scope of the project
1.4    Limitation of the design
1.5    Definition of important terms
1.6    Project report organization

CHAPTER TWO: LITERATURE REVIEW
2.1 Origin
2.2 Overview of the project
2.3 Merits and demerits of the project
CHAPTER THREE: DESIGN METHODOLOGY
3.1 Concept of the project
3.2 Project specification
3.3 Design pattern
3.4 Design approach
3.5 Design processes
3.6 Packaging
CHAPTER FOUR: SYSTEM IMPLEMENTATIO AND DESIGN
4.1 Circuit description
4.2 Component analysis
4.2.1 Power supply
4.2.2 Rectifiers
4.2.3 Capacitors
4.2.3 Voltage regulation
4.2.4 Resistors
4.2.5 Logic gates
4.2.6 Transistors
4.2.7 Relays
4.2.7 Switchers
4.3 Block diagram of the project
4.4 Modules and their functions
4.5 Circuit diagram
4.6 Circuit analysis and how it works
CHAPTER FIVE: SYSTEM TEST AND BILL OF ENGINNERING
5.1 Component test
5.1.1 Transformer test
5.1.2 Diode test
5.1.3 Capacitor test
5.2 Bill of engineering
CHAPTER SIX: SUMMARY
6.1 Summary
6.2 Recommendation
6.3 Problems encounter
6.4 Solutions archived
6.5 Conclusion
Appendix A: System component list
Appendix B: Component cost analysis table
Appendix C: Circuit diagram layout
Appendix D: Circuit wiring schedule
Appendix E: Complete system schematic diagram
Appendix F: System source code
Appendix G: System User’s guild
Appendix H: Project package photograph
Appendix I: Microcontroller/Microprocessor instruction set





















































































































12 VOLTS AUTOMATIC BATTERY CHARGING SYSTEM
For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Share This
  • Type: Project
  • Department: Electrical Engineering
  • Project ID: ELE0221
  • Access Fee: ₦5,000 ($14)
  • Pages: 56 Pages
  • Format: Microsoft Word
  • Views: 698

500
Leave a comment...

    Related Works

    ABSTRACT           A battery charger is an electrical device employed for charging batteries.  This batteries that are usually charged by battery changer are the storage battery charger are the storage batteries also known as “accumulator” the battery changer changes.  The alternating current form the power line into d.c suitable... Continue Reading
    ABSTRACT A battery charger is an electrical device employed for charging batteries. This batteries that are usually charged by battery changer are the storage battery charger are the storage batteries also known as “accumulator” the battery changer changes. The alternating... Continue Reading
    ABSTRACT A battery charger is an electrical device employed for charging batteries.  This batteries that are usually charged by battery changer are the storage battery charger are the storage batteries also known as “accumulator” the battery changer changes.  The alternating current form the power line into d.c suitable for charging. When... Continue Reading
    Design And Construction Of An Intelligent 250 Volts Battery Charger With Micro Processor Using Seven Segment Display   TABLE OF CONTENTS Title page                                             i Certification page                                      ii Dedication... Continue Reading
      ABSTRACT         This project work describes the construction and designing of 12volt car battery charger with USB port for charging mobile phones. The charging process is focus more on 12volt lead car batteries commonly used in vehicles. This design was done by using I.C LM7812 and LM7806 with transformer of 230 volt and series of other... Continue Reading
    Abstract Electric Vehicle (EV) technology is one of the steps in battling climate change through electrification of transport systems. Great advances in energy to size and energy to cost ratios have presented a great opportunity allowing all auto manufacturers to jumped for the idea of electrification as the future of transportation. The journey... Continue Reading
                                                             ABSTRACT This project describes the design and construction of an automatic Battery charger. Automatic Battery chargers are not particularly cheap, but the protection they afford in protecting batteries against overcharging and possible battery damage is highly... Continue Reading
                                                             ABSTRACT This project describes the design and construction of an automatic Battery charger. Automatic Battery chargers are not particularly cheap, but the protection they afford in protecting batteries against overcharging and possible battery damage is highly... Continue Reading
    ABSTRACT The practical importance of a battery charging unit in today’s world cannot be over emphasized. This is so since these batteries or accumulators are immensely needed by automobiles and in science laboratories. This thesis describes the methodical approach to the design and construction of any battery changer. However the procedure... Continue Reading
    ABSTRACT   Automatic voltage inverter is an important area in power system engineering.   It is the process of using a 12v DC from the battery to achieve a 220/230V AC through the help of oscillator, drivers, power transistors and transformer.   The stages are battery to oscillators, oscillators to drivers, drivers to power transistors then... Continue Reading
    Call Us Get this work