Design and construction of an automatic Battery charger

  • Type: Project
  • Department: Physics
  • Project ID: PHY0045
  • Access Fee: ₦5,000 ($14)
  • Pages: 10 Pages
  • Format: Microsoft Word
  • Views: 1.3K
  • Report This work

For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

                                                         ABSTRACT

This project describes the design and construction of an automatic Battery charger. Automatic Battery chargers are not particularly cheap, but the protection they afford in protecting batteries against overcharging and possible battery damage is highly desirable. However the work carried out through the construction and design of an inexpensive alternative to the commercially available fully Automatic Battery Chargers, which will automatically monitor the state of the battery and cut off the charge current at the desired point when the battery is fully charged.


  TABLE OF CONTENT

Content                                                                                                                      Page

Cover page i

Declaration ii

Certification iii

Dedication iv

Acknowledgement v

Abstract vi

Table of content vii


Chapter one

Introduction 1

1.1 Project Motivation 4

1.2 Aim and Objectives 4

1.3 Problem Statement 5


Chapter two

Literature Review 6

2.1 Theory and Design 7

2.1.1 Definition of a Battery 7

2.2 Chemistry of a Lead-Acid Cell 8

2.2.1 When Discharging 8

2.2.2 When Recharging 10

2.3 Effect of Temperature on Battery Operation 11

2.3.1 Battery Failure 12

2.4 Transformer 12

2.5 Rectification 14

2.5.1 Full-Wave Bridge Rectifier 15

2.6 Zener Diode 17

2.7 Silicon Controlled Rectifier (SCR) 19

2.8 Capacitors 21

2.9 Diodes 22


Chapter three

3.1 Methodology (Circuit Construction) 25

3.1.1 AC to DC Unit 25

3.1.2 Charge Monitor 28


Chapter Four

4.1 Result and Discussion 30

4.1.1 Test for the Transformer 30

4.1.2 Test for the Rectifier 30

4.1.4 Operational Amplifier Test 30

4.2 Problems Encountered 31

4.3 Components Used 31



Chapter Five

5.0 Application, Conclusion and Recommendation 32

5.1 Application 32

5.2 Conclusion 32

5.3 Recommendation 32

5.4 References


Design and construction of an automatic Battery charger
For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Share This
  • Type: Project
  • Department: Physics
  • Project ID: PHY0045
  • Access Fee: ₦5,000 ($14)
  • Pages: 10 Pages
  • Format: Microsoft Word
  • Views: 1.3K

500
Leave a comment...

    Related Works

    ABSTRACT The practical importance of a battery charging unit in today’s world cannot be over emphasized. This is so since these batteries or accumulators are immensely needed by automobiles and in science laboratories. This thesis describes the methodical approach to the design and construction of any battery changer. However the procedure... Continue Reading
    ABSTRACT           A battery charger is an electrical device employed for charging batteries.  This batteries that are usually charged by battery changer are the storage battery charger are the storage batteries also known as “accumulator” the battery changer changes.  The alternating current form the power line into d.c suitable... Continue Reading
    ABSTRACT Automatic voltage inverter is an important area in power system engineering. It is the process of using a 12v DC from the battery to achieve a 220/230V AC through the help of oscillator, drivers, power transistors and transformer. The stages are battery to oscillators, oscillators to drivers, drivers to power transistors then from power... Continue Reading
    ABSTRACT   Automatic voltage inverter is an important area in power system engineering.   It is the process of using a 12v DC from the battery to achieve a 220/230V AC through the help of oscillator, drivers, power transistors and transformer.   The stages are battery to oscillators, oscillators to drivers, drivers to power transistors then... Continue Reading
    ABSTRACT This project presents the design and construction of a battery charger. A battery charger is an electrical/electronic device used to put energy into a secondary cell or rechargeable battery by forcing an electric current through it.  The system  consists of a step down transformer, an AC to DC converter and a DC voltage regulator. The... Continue Reading
    ABSTRACT This project which comprise of many chapters that deals extensively with designs and construction of battery charger with auto-cut off which is capable of charging a 12 volts battery. In this construction research, designs was carried out which historic research was used to break down and evaluate to a low level understating of what an... Continue Reading
    ABSTRACT A battery charger is an electrical device employed for charging batteries.  This batteries that are usually charged by battery changer are the storage battery charger are the storage batteries also known as “accumulator” the battery changer changes.  The alternating current form the power line into d.c suitable for charging. When... Continue Reading
    ABSTRACT A battery charger is an electrical device employed for charging batteries. This batteries that are usually charged by battery changer are the storage battery charger are the storage batteries also known as “accumulator” the battery changer changes. The alternating... Continue Reading
      ABSTRACT         This project work describes the construction and designing of 12volt car battery charger with USB port for charging mobile phones. The charging process is focus more on 12volt lead car batteries commonly used in vehicles. This design was done by using I.C LM7812 and LM7806 with transformer of 230 volt and series of other... Continue Reading
    Design And Construction Of An Intelligent 250 Volts Battery Charger With Micro Processor Using Seven Segment Display   TABLE OF CONTENTS Title page                                             i Certification page                                      ii Dedication... Continue Reading
    Call Us Get this work