DESIGN AND FABRICATION OF A CREEP TESTING EQUIPMENT

  • Type: Project
  • Department: Mechanical Engineering
  • Project ID: MCE0020
  • Access Fee: ₦5,000 ($14)
  • Chapters: 5 Chapters
  • Pages: 28 Pages
  • Methodology: scientific analysis
  • Reference: YES
  • Format: Microsoft Word
  • Views: 2.7K
  • Report This work

For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853
DESIGN AND FABRICATION OF A CREEP TESTING EQUIPMENT
ABSTRACT

            The process involves in the design and fabrication of a creep testing equipment ranges from carrying out the feasibility studying of the project to be designed in terms of functionality.  Since it is used in the testing of failure of material under loading different engineering materials employed in the design and fabrication includes bending moments and deflection of bean etc.
            The main purpose of this project is to design mechanical system and electrical system capable of estimating the failure respective of the material under constant loading, which creep is defined as the failure or deformation of material under constant loading occurs.
            Creep is defined as time dependent deformation of materials under constant load (plastics).
TABLE OF CONTENTS
CHAPTER ONE
Introduction                                                                                                    
Primary Creep                                                                        
Secondary Creep                                                                    
Tertiary Creep                                                
CHAPTER TWO
Literature Review                                                       
Japan Creep Research Association (JCRA)               
Denison Mayes Group (DMG)                                              
Applied Test System (ATPS)                        
CHAPTER THREE
Material selection                                                        
Components                                                                                       
Standard Parts                                                                       
CHAPTER FOUR
Fabrication Parts                                                                    
Sequence of Operation                                                          
CHAPTER FIVE
Design Calculation                             
Experimental Result   
CHAPTER SIX
Material Cost                                                  
Labour Cost    
Recommendation                    
Conclusion                                                      
References                              
CHAPTER ONE
INTRODUCTION
            Creep is defined as time – dependent deformation of a material under a constant stress or load.  At temperature less than 40 percent of the absolute melting point, the extent of creep if negligible, but at temperatures higher than this is commonly thought of as a high temperature test.
            The creep material measuring device is a simple unit designed for demonstrating and investigating the creep characteristics of lead polypropylene specimen at room temperature.  A temperature module is provided to enable the investigation/effects of the temperature as a creep rate.
            A failure may also be due to a phenomenon called creep, which is the plastic flow of a material under load at elevated temperatures in addition, the actual shape of a part may be responsible for failure for example stress concentrations due to sudden changes in contour must be taken into account.  This is especially true when dynamic loads with direction reversals exist and the material is not very ductile.
            The single specimen creep measuring apparatus/machine is a table top apparatus measuring dimensionally 740 x 470 x 310 mm and approximated weight of 14.5kg.  This simple machine uses specimens of lead and various types of plastics which creep significantly at temperature and under loads.
            The design is based on a simple lever principle having a mechanical advantage of 8:1 which provides a steady and uniform tensile load.  The extension of the specimen under load is measured by a dial guage.
            It is made up of vertical column which is the main supporting frame, a lever beam, a stop watch, dial guage, a set of weigh hanger, connecting strip, Aluminum block, Ammeter, circuit breaker, volt meter, temperature control, thermocouple, Heating element and a panel made of mild steel shut to house the above mentioned components.  To ensure correct loading of the specimen, the load beam is filted with harden connecting strip which load is applied by means of a set of weight hanger as required.  This apparatus is especially designed for teaching.
            Generally for satisfactory use of this equipment, a bunch of approximately 1 x 0.6m is recommended.
            A creep curve is a plot of the elongation of a tensile specimen versus time, at a given temperature, under a constant load.  The four stages of creep curve is (1) initial elongation flowing the application at load, (2) transient or primary creep, (3) steady state or secondary creep, and (4) tertiary creep.
 THE PRIMARY CREEP
Fig 1.1:            This is the stage of the curve over which the creep rate, is de/dt, is continuously decreasing as show in the figure above.  This is of interest to a designer since it forms part of the extension reached in a given time and may affect clearance.
THE SECONDARY CREEP
Fig 1.2:            This section is a period of approximately constant creep rate and is termed secondary creep; the creep rate is at a minimum over this region.
            This secondary stage is the region at which creep occurs at more or less “STEADY STATE”.  This is the important part of the curve for most applications.
THE TERTIARY CREEP
Fig 1.3:            This stage represents a continuously increasing creep rate and terminates in fracture of the specimen as shown in the figure above.  This tends to be the final stage of the creep curve when the rate of extension accelerates and finally leads to fracture.

DESIGN AND FABRICATION OF A CREEP TESTING EQUIPMENT
For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Share This
  • Type: Project
  • Department: Mechanical Engineering
  • Project ID: MCE0020
  • Access Fee: ₦5,000 ($14)
  • Chapters: 5 Chapters
  • Pages: 28 Pages
  • Methodology: scientific analysis
  • Reference: YES
  • Format: Microsoft Word
  • Views: 2.7K

500
Leave a comment...

    Related Works

    ABSTRACT The process involved in the design and fabrication of a creep material testing equipment ranges from carrying out the feasibility studies of the project to the designed and especially of ensuring its functionality.  Since it is used in the testing of failure of material under loading, different engineering principles employed in the... Continue Reading
    ABSTRACT The process involved in the design and fabrication of a creep material testing equipment ranges from carrying out the feasibility studies of the project to the designed and especially of ensuring its functionality. Since it is used in the testing of failure of material under loading, different engineering principles employed in the design... Continue Reading
    ABSTRACT This project work deals with the design and fabrication of a suitable journal bearing test apparatus which can help in visualizing the behavior of journal bearing and its characteristics, and in determining the bearing parameters such as load bearing capacity, maximum oil film temperature, viscosity of lubricant, oil film pressure, and... Continue Reading
    ABSTRACT This project work deals with the design and fabrication of a suitable journal bearing test apparatus which can help in visualizing the behavior of journal bearing and its characteristics, and in determining the bearing parameters such as load bearing capacity, maximum oil film temperature, viscosity of lubricant, oil film pressure, and... Continue Reading
    ABSTRACT This project work deals with the design and fabrication of a suitable journal bearing test apparatus which can help in visualizing the behavior of journal bearing and its characteristics, and in determining the bearing parameters such as load bearing capacity, maximum oil film temperature, viscosity of lubricant, oil film pressure, and... Continue Reading
    ABSTRACT A 1.05 cubic metre capacity storage facility which is to increase the shelf life of stored vegetables as designed fabricated and tested. The equipment operates on the principle of evaporative cooling and increasing the relative humidity of the interior of the equipment. The door and the back wall were of particle board of 12mm thickness... Continue Reading
    ABSTRACT A 1.05 cubic metre capacity storage facility which is to increase the shelf life of stored vegetables as designed fabricated and tested. The equipment operates on the principle of evaporative cooling and increasing the relative humidity of the interior of the equipment. The door and the back wall were of particle board of 12mm thickness... Continue Reading
    ABSTRACT An equipment design project was carried out to design an inverter (Bioreator) or the production of 100,00 metric tones per year of ethanol from sugar cane. An inverter is a part of process equipment used in ethanol production from sugar cane. While the rest process equipment include crusher, filter, centrifuge, fermented, distribution... Continue Reading
    ABSTRACT An equipment design project was carried out to design an inverter (Bioreator) or the production of 100,00 metric tones per year of ethanol from sugar cane. An inverter is a part of process equipment used in ethanol production from sugar cane.  While the rest process equipment include crusher, filter, centrifuge, fermented, distribution... Continue Reading
    ABSTRACT    Due to the scarcity of water in Nigeria, there is a need for an irrigation system that conserves water for efficient crop production. In the course of this research work, a drip irrigation system was constructed and tested with the sole aim of using cheaply available materials to determine the variation in emitter discharge at... Continue Reading
    Call Us Get this work