DESIGN AND CONSTRUCT A MULTIREMOTE CONTROLLER USING INFRA-RED MODE OF TRANSMISSION

  • Type: Project
  • Department: Electrical Engineering
  • Project ID: ELE0277
  • Access Fee: ₦5,000 ($14)
  • Pages: 95 Pages
  • Format: Microsoft Word
  • Views: 692
  • Report This work

For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853
ABSTRACT

Microcontroller based remote control system is a project design of a system that uses infra red transmission and reception principle to switch on or off other appliances. It is a wireless mode of switching appliances to a desired state. When a number is pressed in the transmitter section, the receiver section decodes the signal and utilizes it in controlling the desired appliances.
Several functional blocks of circuit are put together to ensure that the design works as the designer intended. These blocks include; the power supply unit, signal transmission section, signal reception section, the microcontroller unit and the voltage switching section. The power supply unit to the system comprises of a 12volts step-down transformer, a bridge rectifier circuit, a filter capacitor and a voltage regulator.
The signal transmission section sends out signals through an infra red transmitter situated in a remote. This signal transmitted is in the form of a frequency and only devices operating within that range of frequency can detect the transmitted signal.
Signal reception unit uses an infra red transmitter to receive the frequencies transmitted by the remote. The microcontroller section is used to decode the frequencies received by the infra red receiver and this is used to turn on or off the desired appliance. The microcontroller used is atmel89s51.
The voltage switching section uses relay in its operation. It receives signal from the microcontroller and ensures that appropriate voltage is supplied to the appliance being controlled by the operator.

DESIGN AND CONSTRUCT A MULTIREMOTE CONTROLLER USING INFRA-RED MODE OF TRANSMISSION
For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Share This
  • Type: Project
  • Department: Electrical Engineering
  • Project ID: ELE0277
  • Access Fee: ₦5,000 ($14)
  • Pages: 95 Pages
  • Format: Microsoft Word
  • Views: 692

500
Leave a comment...

    Related Works

    ABSTRACT Microcontroller based remote control system is a project design of a system that uses infra red transmission and reception principle to switch on or off other appliances. It is a wireless mode of switching appliances to a desired state. When a number is pressed in the transmitter section, the receiver section decodes the signal and... Continue Reading
    ABSTRACT Microcontroller based remote control system is a project design of a system that uses infra red transmission and reception principle to switch on or off other appliances. It is a wireless mode of switching appliances to a desired state. When a number is pressed in the transmitter section, the receiver section decodes the signal and... Continue Reading
    CHAPTER ONE INTRODUCTION 1.1   Background of Study This chapter gives an overview of thisproject titled a queue management system (microcontroller based intelligent queue management system). This report started with the background of our study to give the readers an idea of what this project is all about before going into its technical details.... Continue Reading
    CHAPTER ONE 1.0 INTRODUCTION This project gives the insight on the design and construction of a transmission power line vandalism detector system. Vandalism means destructive action. It is a hateful and deliberate defacement/destruction of somebody else’s property or national assets like thehigh-voltage transmission power lines, transmission... Continue Reading
    ABSTRACT  T-junction traffic light controller is such a device that will play a significant role in controlling traffic at junctions, to ease the expected increased rush at such junctions and reduce to minimum disorderliness that may arise, as well as allowing the pedestrians a right of the way at intervals rather than being struck down when in a... Continue Reading
    ABSTRACT The very fundamental reasons behind this project assignment is to expose student to the very important aspect of private and independent research work not only theories but also subsequent translation of the theoretical research work into a particular function system. The project construction of automatic fence light controller has been... Continue Reading
    ABSTRACT  The very fundamental reasons behind this project assignment is to expose student to the very important aspect of private and independent research work not only theories but also subsequent translation of the theoretical research work into a particular function system. The project construction of automatic fence light controller has been... Continue Reading
    INTRODUCTION The purpose of this project is to produce a narrative description of the design and construction of a microcontroller based dot matrix advert display. Firstly computer aided design is the modeling of physical system on Computers allowing both interactive and automatic analysis of design variant and the expression of design in a form... Continue Reading
    ABSTRACT:  A traffic light system is an electronic circuitry designed and configured to control the flow of the traffic (vehicular and human) at roads intersection without the physical presence of a traffic warden. This is made possible through the help of a signaling device which is mounted at roads intersection. It is achieved using... Continue Reading
    ABSTRACT This research is focused at designing of water storage facilities of size 875,000 litres (750,000 litres for underground water storage, and 125,000 Litres for elevated steel tank) of treated wastewater and its transmission system for the storage and re-use of treated wastewater. The project is aimed to structurally design water storage... Continue Reading
    Call Us Get this work