FABRICATION OF CANDLE MOULD WITH TWENTY FOUR (24) HOLES

  • Type: Project
  • Department: Chemical Engineering
  • Project ID: CNG0409
  • Access Fee: ₦5,000 ($14)
  • Pages: 29 Pages
  • Format: Microsoft Word
  • Views: 207
  • Report This work

For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853
ABSTRACT

The candle mould has twenty four (24) holes which could produce twenty four (24) quality candle sticks
Aluminum, a non ferrous metal was used as the construction material for the mould the type of casting technique used was green sand mould method.
In the process of moulding the pattern was placed in the flask which contained the green sand.  The flask was turned upside down and the reverse side of the pattern was formed.  This part is called the positive part, the other part of the pattern formed on the moist sand is called the negative part, the two parts were then joint together to form the cope and the drag.
A gate or opening was provided for the pouring of the molten aluminum into the mould.  Gases and fumes were able to escape through the vents.
It was ensured that the molten aluminum filled all parts of the mould with the least delay.  All part of the candle mould  were machined after casting to get a perfect exterior and interior surface finish.
The fabrication  of the   candle mould cost seven thousand (N7,000) naira for both material and labour.

TABLE OF CONTENTS
Title page
Dedication
Acknowledgement
Abstract 
Table of content

CHAPTER ONE
1.0 Introduction 

CHAPTER TWO
2.0 Literature review
2.1 Theory of casting processes in the construction of the candle mould
2.2 Properties of sand mould

CHAPTER THREE
3.0 Materials of fabrication
3.1 Selection of aluminum as a construction raw material
3.2 Treatment of aluminum prior to casting.
3.3 Fabrication test

CHAPTER FOUR
4.0 Plug preparation 
4.1 Fabrication procedure 
4.2 Materials use for the contraction of candle mould
4.3 Purification of aluminum
4.4 Constructions method
4.5 Machining operation
4.6 Safety precaution 

CHAPTER FIVE
5.0 Method of operation
5.1 Quality control measures
5.2 Care and maintenance of the candle mould

CHAPTER SIX
6.0 Cost analysis

CHAPTER SEVEN
7.0 Conclusion
7.1 Recommendation
     Appendix 
     References

FABRICATION OF CANDLE MOULD WITH TWENTY FOUR (24) HOLES
For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Share This
  • Type: Project
  • Department: Chemical Engineering
  • Project ID: CNG0409
  • Access Fee: ₦5,000 ($14)
  • Pages: 29 Pages
  • Format: Microsoft Word
  • Views: 207

500
Leave a comment...

    Related Works

    ABSTRACT The candle mould has twenty four (24) holes which could produce twenty four (24) quality candle sticks Aluminum, a non ferrous metal was used as the construction material for the mould the type of casting technique used was green sand mould method. In the process of moulding the pattern was placed in the flask which contained the green... Continue Reading
    ABSTRACT The candle mould has twenty four (24) holes which could produce twenty four (24) quality candle sticks Aluminum, a non ferrous metal was used as the construction material for the mould the type of casting technique used was green sand mould method. In the process of moulding the pattern was placed in the flask which contained the green... Continue Reading
    ABSTRACT The candle mould has twenty four (24) holes which could produce twenty four (24) quality candle sticks Aluminum, a non ferrous metal was used as the construction material for the mould the type of casting technique used was green sand mould method. In the process of moulding the... Continue Reading
    ABSTRACT The candle molding machine is a vital device which cannot be done without, in any nation. This is because of the indispensable role candle plays, especially when there is no either source of light. In order to enhance adequate supply to both urban and rural consumers, the production of a candle molding machine is important. The major... Continue Reading
    ABSTRACT The candle molding machine is a vital device which cannot be done without, in any nation. This is because of the indispensable role candle plays, especially when there is no either source of light. In order to enhance adequate supply to both urban and rural consumers, the... Continue Reading
    THE DESIGN AND FABRICATION OF A CANDLE MOULDING MACHINE ABSTRACT The idea of producing “candle stick” brought the existence of fabricating a “candle moulding machine” which can produce a desired shape of a candle foe the benefit of mankind. In chapter 1, which is the research work of the project carried out, the problem encountered and the... Continue Reading
    ABSTRACT The candle molding machine is a vital device which cannot be done without, in any nation. This is because of the indispensable role candle plays, especially when there is no either source of light. In order to enhance adequate supply to both urban and rural consumers, the production of a candle molding machine is important. The major... Continue Reading
    ABSTRACT           This research relates to a candle composition containing non-hydrogenated oil and at least one of long chain hydrocarbon and long-chain hydrocarbon derivatives. A candle composition having non-hydrogenated oil and a solidifying amount of congealing reagent.... Continue Reading
    ABSTRACT This research relates to a candle composition containing non-hydrogenated oil and at least one of long chain hydrocarbon and long-chain hydrocarbon derivatives. A candle composition having non-hydrogenated oil and a solidifying amount of congealing reagent. A candle... Continue Reading
    this project talks about 100 American stories ... Continue Reading
    Call Us Get this work