CONSTRUCTION OF A 12 VOLT BATTERY CHARGER

  • Type: Project
  • Department: Electrical Engineering
  • Project ID: ELE0400
  • Access Fee: ₦5,000 ($14)
  • Pages: 18 Pages
  • Format: Microsoft Word
  • Views: 173
  • Report This work

For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853
ABSTRACT 
The battery which has always serve as a sources of electrical current has in the past been invalid and inmost cases seen as monument after implicating as battery wound have to be brought over and over again the implicating has been that of lot of money is been spent for this purpose we give appraise for the advancement of technology which today had led to the production of battery which could be made functional after it energy may be used up this has been made possible by recharging the battery.

Therefore the recharging production of battery charge which adequately take care of recharging battery has come stay in this project we will produce a batter charger and examine the component it is made up of the process involved and their stages as well

 
TABLE OF CONTENT 
Cover page
Title page
Approval page
Dedication
Acknowledgement 
Abstract 
Table of content

CHAPTER ONE
1.0Introduction 
1.1Component of the battery charge
1.2Transformer
1.3Rectifier
1.4Capacitor   
1.5Resistor 
1.6Diode 
1.7 Light emitting diode 

CHAPTER TWO
2.0Construction 
2.1Construction procedure 
2.2Block diagram (not included) 
2.3Schematic diagram  (not included) 
2.4Ham put diagram (not included) 

CHAPTER THREE   
3.0Principle of operation 
3.1Test and result 
3.2Procedure for charge

CHAPTER FOUR
4.0Application 
4.1Short coming 
4.2Maintenance

CHAPTER FIVE 
5.0Bill of quantity
5.1Precaution 
5.2Conclusion 

CHAPTER SIX 
6.0Bibliography 

CONSTRUCTION OF A 12 VOLT BATTERY CHARGER
For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Share This
  • Type: Project
  • Department: Electrical Engineering
  • Project ID: ELE0400
  • Access Fee: ₦5,000 ($14)
  • Pages: 18 Pages
  • Format: Microsoft Word
  • Views: 173

500
Leave a comment...

    Related Works

      ABSTRACT         This project work describes the construction and designing of 12volt car battery charger with USB port for charging mobile phones. The charging process is focus more on 12volt lead car batteries commonly used in vehicles. This design was done by using I.C LM7812 and LM7806 with transformer of 230 volt and series of other... Continue Reading
    ABSTRACT   This project, 12v battery charge consist of few chapters, deal extensively with the design and construction of a batter charge which is capable of charging a 12v battery. The introductory chapter goes a long why in defining the battery charger and explanations of the mode of operations will be death with as we proceed.     TABLE OF... Continue Reading
    ABSTRACT This project, 12v battery charge consist of few chapters, deal extensively with the design and construction of a batter charge which is capable of charging a 12v battery. The introductory chapter goes a long why in defining the battery charger and explanations of the mode of operations will be death with as we proceed. TABLE OF CONTENT... Continue Reading
    ABSTRACT This project presents the design and construction of a battery charger. A battery charger is an electrical/electronic device used to put energy into a secondary cell or rechargeable battery by forcing an electric current through it.  The system  consists of a step down transformer, an AC to DC converter and a DC voltage regulator. The... Continue Reading
    ABSTRACT This project which comprise of many chapters that deals extensively with designs and construction of battery charger with auto-cut off which is capable of charging a 12 volts battery. In this construction research, designs was carried out which historic research was used to break down and evaluate to a low level understating of what an... Continue Reading
                                                             ABSTRACT This project describes the design and construction of an automatic Battery charger. Automatic Battery chargers are not particularly cheap, but the protection they afford in protecting batteries against overcharging and possible battery damage is highly... Continue Reading
                                                             ABSTRACT This project describes the design and construction of an automatic Battery charger. Automatic Battery chargers are not particularly cheap, but the protection they afford in protecting batteries against overcharging and possible battery damage is highly... Continue Reading
    ABSTRACT The practical importance of a battery charging unit in today’s world cannot be over emphasized. This is so since these batteries or accumulators are immensely needed by automobiles and in science laboratories. This thesis describes the methodical approach to the design and construction of any battery changer. However the procedure... Continue Reading
    ABSTRACT A battery charger is an electrical device employed for charging batteries. This batteries that are usually charged by battery changer are the storage battery charger are the storage batteries also known as “accumulator” the battery changer changes. The alternating... Continue Reading
    ABSTRACT A battery charger is an electrical device employed for charging batteries.  This batteries that are usually charged by battery changer are the storage battery charger are the storage batteries also known as “accumulator” the battery changer changes.  The alternating current form the power line into d.c suitable for charging. When... Continue Reading
    Call Us Get this work