CONSTRUCTION OF A BATTERY CHANGER USING SILICON CONTROLLED REGULATOR (SCR)

  • Type: Project
  • Department: Electrical Engineering
  • Project ID: ELE0402
  • Access Fee: ₦5,000 ($14)
  • Pages: 31 Pages
  • Format: Microsoft Word
  • Views: 159
  • Report This work

For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853
ABSTRACT 
The practical importance of a battery charger in today world cannot be over emphasized. This is so as those batteries accumulators are immensely needed by out auto mobile and in science laboratories.
This thesis describes the methodical approach to the design and construction of  any battery charger. However the procedure fro developed cover the construction  of battery charger for battery sizes ranging from 6 voltage to 24volatge (heavy duty) batteries.
The prototype of a battery charger for these ranges of batteries has been implemented  following the methodical approach as outlined in this thesis and its operational test results are quite satisfactory. adequate care has been taken  in the design and construction to ensure that the resultant battery charger are both reliable and easy to use.
 
TABLE OF CONTENT 
Title Page
Approval page
Dedication 
Acknowledgement
Abstract

Chapter one  
1.0Introduction
1.1Background of the project 
1.2Aim and objective 
1.3Scope of the project 
1.4Organization of the project 

Chapter two
2.0Literature review 
2.1Battery 
2.2The storage battery
2.2.1Nikel Iron Battery 
2.2.2Lead acid battery 
2.3Indications of a fully  charged cell
2.3.1Gassing 
2.3.2Voltage
2.3.3Colour
2.3.4Charger 

Chapter three 
3.1Function block diagram 
3.1.1Power supply unit
3.1.2Ac to Dc rectification 
3.1.3Filter and regulation 
3.2Types  of carrging system 
3.2.1Half wave system
3.2.2Full wave charging system 

Chapter four
4.1Construction of battery charger 
4.1.1Power supply unit (PSU)
4.1.2Detector circuit 
4.2Components of a PSU
4.3Components of detector circuit 

Chapter five  
5.1Summary 
5.2Conclusion 
5.3Component sourcing 
5.4References.

CONSTRUCTION OF A BATTERY CHANGER USING SILICON CONTROLLED REGULATOR (SCR)
For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Share This
  • Type: Project
  • Department: Electrical Engineering
  • Project ID: ELE0402
  • Access Fee: ₦5,000 ($14)
  • Pages: 31 Pages
  • Format: Microsoft Word
  • Views: 159

500
Leave a comment...

    Related Works

    ABSTRACT  The practical importance of a battery charger in today world cannot be over emphasized. This is so as those batteries accumulators are immensely needed by out auto mobile and in science laboratories. This thesis describes the methodical approach to the design and construction of  any battery charger. However the procedure fro developed... Continue Reading
    ABSTRACT The practical importance of a battery charger in today world cannot be over emphasized. This is so as those batteries accumulators are immensely needed by out auto mobile and in science laboratories. This thesis describes the methodical approach to the design and construction of any battery charger. However the procedure fro developed... Continue Reading
    ABSTRACT The AVR is automatic voltage regulator and it is a device which is used to regulate or stabilize electrical power supply for electrical or electronic appliances        In this project, therefore, we are interested in the construction of this all important device. Furthermore, we shall discuss the techniques, processes, switching... Continue Reading
    ABSTRACT This project proposes a new type of voltage regulator based on single-phase converter otherwise known as transformerless AVR that compensates wide range voltage variations. This is not only capable of compensating variations at a much higher bandwidth but also does not experience mechanical wear down and is cost effective. The proposed... Continue Reading
    ABSTRACT The AVR is automatic voltage regulator and it is a device which is used to regulate or stabilize electrical power supply for electrical or electronic appliances In this project, therefore, we are interested in the construction of this all important device. Furthermore, we shall discuss the techniques, processes, switching stages and then... Continue Reading
    ABSTRACT This project is all about Automatic Voltage Regulator (AVR), and is a circuit that monitors the input voltage at any point and display the regulated voltage level on the analog meter. It is mainly for electrical/electronic system that is delicate to abnormal voltage level. It is usually connected as an intermediary between voltage supply... Continue Reading
    ABSTRACT The modern manufacturing environment is dynamic and uncertain. In line with the global trend in manufacturing, this project is carried out to explore into the potentials of robots in manufacturing, service industry, and domestic use. The robot was designed and  constructed to incorporate the use of mobile phones as control mechanism via... Continue Reading
    ABSTRACT The modern manufacturing environment is dynamic and uncertain. In line with the global trend in manufacturing, this project is carried out to explore into the potentials of robots in manufacturing, service industry, and domestic use. The robot was designed and  constructed to incorporate the use of mobile phones as control mechanism via... Continue Reading
    Abstract The project DESIGN AND CONSTRUCTION OF A 20-METRE DISTANCE REMOTELY CONTROLLED METAL DETECTOR is used for detecting metallic objects such as phones, bombs, and other metallic objects that are hidden from view. The design is based on the principle of the Resonant Frequency Oscillator (RFO) metal detectors in which oscillation is a function... Continue Reading
       Abstract The project DESIGN AND CONSTRUCTION OF A 20-METRE DISTANCE REMOTELY  CONTROLLED METAL DETECTOR is used for detecting metallic objects such as phones,  bombs, and other metallic objects that are hidden from view. The design is based on the principle  of the Resonant Frequency Oscillator (RFO) metal detectors in which oscillation is... Continue Reading
    Call Us Get this work