DESIGN AND CONSTRUCTION OF AN AUTOMATIC VOLTAGE STABILIZER

  • Type: Project
  • Department: Electrical Engineering
  • Project ID: ELE0470
  • Access Fee: ₦5,000 ($14)
  • Pages: 30 Pages
  • Format: Microsoft Word
  • Views: 203
  • Report This work

For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853
ABSTRACT
In the world today, the use of power supply in electronics equipment and gadgets has increased and it is still increasing.  These power supplies are not stable as required by these electronics.
This arise the need for the power stabilization as to overcome this problem 
This project handles this problem very well.  Some recommendations were also made on this topic and student and users of electronics equipment will find them useful.

TABLE OF CONTENTS
Cover Page
Title Page
Approval Page
Dedication
Acknowledgment
Abstract 
Table of Contents

CHAPTER ONE
1.0Introduction

CHAPTER TWO
2.0Literature Review
2.1The aims/purpose
2.2Stages in the development of voltage stabilizer
2.3Stabilizer grading
2.4Application

CHAPTER THREE
3.0Basic Theory of Components Us ed
3.1Transistors
3.2Diode
3.3Resistor
3.4Relay
3.5Zener diode
3.6Capacitor
3.7Transformer
3.8Fuse
3.9Other materials us ed

CHAPTER FOUR
4.0Design, Construction and Operation of the Stabilizer
4.1Design/Construction
4.2 The Transformer Stage
4.3Control Stage 
4.4The Relay Stage
4.5Operation
4.6Transformer Stage
4.7Control Stage
4.8Relay Stage

CHAPTER FIVE
5.0Discussion, Conclusion and Recommendation
5.1Discussion
5.2Conclusion
5.3Recommendation

CHAPTER SIX
6.0Cost Analysis, References
6.1Cost Analysis
6.2References


DESIGN AND CONSTRUCTION OF AN AUTOMATIC VOLTAGE STABILIZER
For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Share This
  • Type: Project
  • Department: Electrical Engineering
  • Project ID: ELE0470
  • Access Fee: ₦5,000 ($14)
  • Pages: 30 Pages
  • Format: Microsoft Word
  • Views: 203

500
Leave a comment...

    Related Works

    ABSTRACT This project proposes a new type of voltage regulator based on single-phase converter otherwise known as transformerless AVR that compensates wide range voltage variations. This is not only capable of compensating variations at a much higher bandwidth but also does not experience mechanical wear down and is cost effective. The proposed... Continue Reading
    DESIGN AND CONSTRUCTION OF 1000VA AUTOMATIC VOLTAGE REGULATION ABSTRACT The design and construction of 1000VA Automatic Voltage Regulator is made to power our Electrical and Electronic devices, supplying them with the normal output voltage which ranges from 100V- 240v irrespective of the constant voltage and current fluctuation, failure and... Continue Reading
    ABSTRACT The AVR is automatic voltage regulator and it is a device which is used to regulate or stabilize electrical power supply for electrical or electronic appliances In this project, therefore, we are interested in the construction of this all important device. Furthermore, we shall discuss the techniques, processes, switching stages and then... Continue Reading
    ABSTRACT The AVR is automatic voltage regulator and it is a device which is used to regulate or stabilize electrical power supply for electrical or electronic appliances        In this project, therefore, we are interested in the construction of this all important device. Furthermore, we shall discuss the techniques, processes, switching... Continue Reading
    ABSTRACT This project is all about Automatic Voltage Regulator (AVR), and is a circuit that monitors the input voltage at any point and display the regulated voltage level on the analog meter. It is mainly for electrical/electronic system that is delicate to abnormal voltage level. It is usually connected as an intermediary between voltage supply... Continue Reading
    ABSTRACT Automatic voltage inverter is an important area in power system engineering. It is the process of using a 12v DC from the battery to achieve a 220/230V AC through the help of oscillator, drivers, power transistors and transformer. The stages are battery to oscillators, oscillators to drivers, drivers to power transistors then from power... Continue Reading
    ABSTRACT   Automatic voltage inverter is an important area in power system engineering.   It is the process of using a 12v DC from the battery to achieve a 220/230V AC through the help of oscillator, drivers, power transistors and transformer.   The stages are battery to oscillators, oscillators to drivers, drivers to power transistors then... Continue Reading
    ABSTRACT Despite all attempt of the federal government to have not only an uninterrupted power supply for all cities in Nigeria, but a voltage that is inconformity with the recommended 220/230v for domestic consumption for example. The NEPA Plc is facing some difficulties in generating, transmitting and distributing the required voltage... Continue Reading
    ABSTRACT The AVR is an automatic voltage regulator and it is a device which is used to regulate or stabilize electrical power supply for electrical or electronic appliances. Inthisprojecttherefore,weareinterestedintheconstructionof this allimportantdevice.Furthermore we shalldiscuses the techniques,processes,switching stages and then the working... Continue Reading
    ABSTRACT This project is he design and construction of a voltage inverter system with trickle charging system. This device is design to provide power supply for the need of offices, household etc. In absence of NEPA power supply. It would also prevent harm to our appliances caused by power holding company LTD (NEPA) Random power outage . TABLE OF... Continue Reading
    Call Us Get this work