CONSTRUCTION OF 500W12VINVERTER CHARGER

  • Type: Project
  • Department: Electrical Engineering
  • Project ID: ELE0476
  • Access Fee: ₦5,000 ($14)
  • Pages: 53 Pages
  • Format: Microsoft Word
  • Views: 124
  • Report This work

For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

ABSTRACT 

An inverter is a system which is capable of converting DC voltage from a battery into AC voltage. The Inverter constructed converts 12V dc to 220V Ac. It consists of an oscillator section using 8V dc to produce 50Hz sine wave. The sine wave is amplified by Tip 41 and used to drive IRPF 250 MOSFET power transistors capable of delivering 500W norminally.The mosfet switches the 12V dc across the high current transformer which then produces the Ac at its output. The output of the transformer is a square wave but has been converted to a near sine wave using some RC circuit.
There is also a provision in the system to charge the battery when PHCN is on as the inverter is expected to function only PHCN is off.

TABLE OF CONTENT
Cover page Title page I
Approval II
Dedication III
Acknowledgement IV
Abstract V T
able of content VI
List of figures VII

CHAPTER ONE: INTRODUCTION
1.0 Background of the stud……………………….2
1.1 Statement of problem……………………........3
1.2 Aims and objectives…………………………...4
 1.3 Scope of work …………………………………4
1.4 Importance of work………………………........4
1.5 Organization of study …………………………6

CHAPTER TWO: LITERATURE REVIEW
 2.0 Brief History of Inverters………………………8
2.1 Inverter application and uses ………………….8
2.2 Types of inverter ………………………………9
2.3 Inverter versus other related appliances………………..10
2.3.1 Generator and inverter………………………………….10
2.3.2 Inverter and ups………………………………………...12
2.4 Mode of operation of an inverter……………………….13
2.4.1 When the AC mains supply is available………………..14
2.4.2 When the AC mains supply is not available …………...14
2.5 Component Analysis …………………………………...16
2.5.1 Ideal diodes ……………………………………….........16
2.5.2 Resistors……………………………………...................18
2.5.3 Capacitors………………………………………………..19
2.5.4 Transistors…………………………………………….....20
2.5.5 Voltage regulator …………………………….................22
2.5.6 Transformer …………………………………………….23
2.5.7 Relay…………………………………………………….24
2.5.7.1 Battery………………………………………………..26

CHAPTER THREE: SYSTEM OPERATION
3.0 Block diagram and operation…………………………….27
3.1 When the AC mains supply is available…………………….27
3.2 When the AC mains supply is unavailable………………….28
3.3 Complete circuit diagram ………………………………..33
3.3.1 System operation using circuit diagram……………..34

CHAPTER FOUR: DESIGN ANALYSIS AND IMPLEMENTATION
4.0 Design specifications and requirements ……………35
4.1 Design of the power supply unit ……………………35
4.2 Design of 50 Hz oscillator…………………………..37
4.3 Days (hours) of autonomy …………………………39
4.4 Depth of discharge…………………………………...40

CHAPTER FIVE: TESTING AND RESULT
5.0 Drive or amplifier test………………………………..43
5.1 Oscillator circuit test…………………………………43
5.3 Transformer test………………………………………44
5.4 Entire system testing………………………………….44
 5.4 Battery charging evaluation ………………………….44
5.5 System evaluation ……………………………………44
5.6 Packaging …………………………………………….45
5.7 Cost of project ……………………………………….46
5.8 Maintenance cost …………………………………….49
5.9 Running cost …………………………………………49

CHAPTER SIX: CONCLUSION
6.0 Conclusion ……………………………………………50
6.1 Recommendation …………………………………….50
6.2 Problem encountered …………………………………51
6.3 Limitation/ Constraints………………………………..51
6.4 Suggestion for further improvement ………………….51
Reference
CONSTRUCTION OF 500W12VINVERTER CHARGER
For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Share This
  • Type: Project
  • Department: Electrical Engineering
  • Project ID: ELE0476
  • Access Fee: ₦5,000 ($14)
  • Pages: 53 Pages
  • Format: Microsoft Word
  • Views: 124

500
Leave a comment...

    Related Works

    ABSTRACT   This project, 12v battery charge consist of few chapters, deal extensively with the design and construction of a batter charge which is capable of charging a 12v battery. The introductory chapter goes a long why in defining the battery charger and explanations of the mode of operations will be death with as we proceed.     TABLE OF... Continue Reading
    ABSTRACT This project, 12v battery charge consist of few chapters, deal extensively with the design and construction of a batter charge which is capable of charging a 12v battery. The introductory chapter goes a long why in defining the battery charger and explanations of the mode of operations will be death with as we proceed. TABLE OF CONTENT... Continue Reading
    ABSTRACT The battery which has always serve as a sources of electrical current has in the past been invalid and inmost cases seen as monument after implicating as battery wound have to be brought over and over again the implicating has been that of lot of money is been spent for this purpose we give appraise for the advancement of technology which... Continue Reading
    ABSTRACT  The battery which has always serve as a sources of electrical current has in the past been invalid and inmost cases seen as monument after implicating as battery wound have to be brought over and over again the implicating has been that of lot of money is been spent for this purpose we give appraise for the advancement of technology... Continue Reading
    ABSTRACT This project presents the design and construction of a battery charger. A battery charger is an electrical/electronic device used to put energy into a secondary cell or rechargeable battery by forcing an electric current through it.  The system  consists of a step down transformer, an AC to DC converter and a DC voltage regulator. The... Continue Reading
    ABSTRACT The practical importance of a battery charging unit in today’s world cannot be over emphasized. This is so since these batteries or accumulators are immensely needed by automobiles and in science laboratories. This thesis describes the methodical approach to the design and construction of any battery changer. However the procedure... Continue Reading
                                                             ABSTRACT This project describes the design and construction of an automatic Battery charger. Automatic Battery chargers are not particularly cheap, but the protection they afford in protecting batteries against overcharging and possible battery damage is highly... Continue Reading
    ABSTRACT This project which comprise of many chapters that deals extensively with designs and construction of battery charger with auto-cut off which is capable of charging a 12 volts battery. In this construction research, designs was carried out which historic research was used to break down and evaluate to a low level understating of what an... Continue Reading
                                                             ABSTRACT This project describes the design and construction of an automatic Battery charger. Automatic Battery chargers are not particularly cheap, but the protection they afford in protecting batteries against overcharging and possible battery damage is highly... Continue Reading
    ABSTRACT A battery charger is an electrical device employed for charging batteries. This batteries that are usually charged by battery changer are the storage battery charger are the storage batteries also known as “accumulator” the battery changer changes. The alternating... Continue Reading
    Call Us Get this work