DESIGN AND CONSTRUCTION OF 20WATTS WIRELESS PUBLIC ADDRESS SYSTEM

  • Type: Project
  • Department: Electrical Engineering
  • Project ID: ELE0486
  • Access Fee: ₦5,000 ($14)
  • Pages: 44 Pages
  • Format: Microsoft Word
  • Views: 197
  • Report This work

For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

ABSTRACT
It has become inevitable that there would be communication and due to the inherent limitation of the human voice, the public address system came to being. A public address or “P.A SYSTEM” is an electronic amplification system with a mixer ,amplifier and loudspeakers, used to reinforce a given sound , e.g a person making a speech, pre-recorded music ,or message and distributing the sound throughout a venue . The voice signal is passed through a microphone , which converts the sound energy to electrical energy, the energy electrical signal being transmitted is been received and amplified by the amplifier circuit. The amplifier’s output is fed into the loudspeaker which converts the electrical energy back to the original form but amplified sound energy. This project is made up of the power supply unit, the pre-amplifier and power amplifier units, and the tone control unit. This system is capable of delivering 20W of electrical power into a 8 ohm load(loudspeaker).

TABLE OF CONTENTS
Certification Page------------------------------------------------------------------------ i
Dedication ---------------------------------------------------------------------------------ii
Acknowledgement------------------------------------------------------------------------iii
Abstract-------------------------------------------------------------------------------------iv
Table of contents---------------------------------------------------------------------------v
List of Table--------------------------------------------------------------------------------vii
List of figures------------------------------------------------------------------------------viii

CHAPTER 1: INTRODUCTION …………………………………………...1
1.1 BACKGROUND OF THE STUDY
1.2 Aims and Objectives……………………………………………..5
1.3 Justification ……………………………………………..6
1.4 Scope of project …………………………………………….7
1.5 System block diagram……………………………………………7
1.6 Project Work Organization ………………………………………8

CHAPTER 2: LITERATURE REVIEW ……………………………………9
2.1 Ancient medium of information transmission …………………….9
2.2 Modern day medium Approach …………………………………...9
2.2.1 Problems associated with earlier systems…………………..……10
2.2.2 Working principles of the modern systems………………………10
2.3 Public Address System…………………………………………..11
2.3.1 The transmitter system…………………………………………..12
2.3.2 The Receiver system…………………………………………….13
2.3.3 The Antenna……………………………………………………..14
2.3.3.1 Functions of Antenna……………………………………………15
2.3.4 The tone control and mixer stage………………………………..15
2.3.5 The audio amplifier……………………………………………..16
2.3.6 The loudspeaker…………………………………………………17
2.4 Modulation………………………………………………………17
2.4.1 Frequency modulation…………………………………………..18

CHAPTER 3: SYSTEM DESCRIPTION AND IMPLEMENTATION….19
3.1 Transistor power amplifier……………………………………….19
3.2 MOSFET power amplifier………………………………………..19
3.3 Bipolar junction transistor………………………………………...21
3.4 Operational Amplifier……………………………………………..23
3.4.1 Class A amplifier………………………………………………….24
3.5 Implementation Method…………………………………………..24

CHAPTER 4: CIRCUIT DESIGN AND ANALYSIS………………………...26
4.1 Power Supply unit design………………………………………….26
4.2 Transmitter design ………………………………………………..27
4.3 Amplifier circuit design…………………………………………....29
4.4 Receiver principles………………………………………………...31
4.5 Demodulation……………………………………………………...32
4.6 Transmitter circuitry…………………………………………….…33
4.7 The input stage…………………………………………………….34
4.8 Mixing stage………………………………………………………34
4.9 Audio power amplifier…………………………………………….36

CHAPTER 5: CONSTRUCTION AND TESTING…………………………37
5.1 The power supply …………………………………………………37
5.2 The output power amplifier………………………………………..37
5.3 Dissipation of excessive heat………………………………………38
5.4 Entire circuit testing………………………………………………..38
5.5 Performance Evaluation…………………………………………...38
5.6 Packaging……………………………………………………….....40

CHAPTER 6: CONCLUSION AND RECOMMENDATION……………..41
6.1 Bill of Engineering measurement and Evaluation (BEME)……….41
6.2 Problems Encountered and Solution……………………………….42
6.3 Audio feedback and prevention……………………………………43
6.5 Conclusion…………………………………………………………44
6.6 Recommendation / Reference ……………………………………44
DESIGN AND CONSTRUCTION OF 20WATTS WIRELESS PUBLIC ADDRESS SYSTEM
For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Share This
  • Type: Project
  • Department: Electrical Engineering
  • Project ID: ELE0486
  • Access Fee: ₦5,000 ($14)
  • Pages: 44 Pages
  • Format: Microsoft Word
  • Views: 197

500
Leave a comment...

    Related Works

    ABSTRACT It has become inevitable that there would be communication and due to the inherent limitation of the human voice, the public address system came to being. A public address or “P.A SYSTEM” is an electronic amplification system with a mixer  ,amplifier and loudspeakers, used to reinforce a given sound , e.g a person making a speech,... Continue Reading
    INTRODUCTION A public address system is an electronics sound amplification and distribution system with a microphone, amplifier and loud speaker used to allow a person to address a large public. The public address system consists of three main parts namely, the microphone (input transducer), amplifier and the loudspeaker (output transducer). The... Continue Reading
    INTRODUCTION A public address system is an electronics sound amplification and distribution system with a microphone, amplifier and loud speaker used to allow a person to address a large public. The public address system consists of three main parts namely, the microphone (input transducer), amplifier and the loudspeaker (output transducer). The... Continue Reading
    ABSTRACT This project intended to simplify the description and working principle of FM wireless microphone, which works on a fixed frequency modulation (FM) band. TABLE OF CONTENTS Approval Sheet Title Page Dedication Acknowledgement Abstract CHAPTER ONE 1.0INTRODUCTION 1.1Aim and Objective of Investigation CHAPTER TWO 2.0Transmitter... Continue Reading
      ABSTRACT This project intended to simplify the description and working principle of FM wireless microphone, which works on a fixed frequency modulation (FM) band.    TABLE OF CONTENTS Approval Sheet  Title Page Dedication  Acknowledgement Abstract  CHAPTER ONE 1.0INTRODUCTION  1.1Aim and Objective of Investigation  CHAPTER TWO ... Continue Reading
    Abstract  Consumers’ complaints of estimated bills from the Utility have risen to an alarming extent in recent years. On the other hand, Utility incurs huge losses attributing it to electric energy consumption theft among consumers. These complaints by the utility and the consumer led to the quest for a system that in addition to recording... Continue Reading
    ABSTRACT The purpose of this project is to design and construction of a central wireless switch for electrical and electronic appliances. A central wireless switch for electrical and electronic appliance is a GSM based online power control switch system that controls the entire appliance in the EEE general office using GSM network. It will act as... Continue Reading
    The aim of this project is to shows the possibility of wireless power transfer through the design of a wireless charging pad.  In this project write-up, the methodology and principle of operation is wireless power transfer through inductive couple, a feasible design is modelled accordingly. The inductive couple technique is used because it is the... Continue Reading
    The aim of this project is to shows the possibility of wireless power transfer through the design of a wireless charging pad.  In this project write-up, the methodology and principle of operation is wireless power transfer through inductive couple, a feasible design is modelled accordingly. The inductive couple technique is used because it is the... Continue Reading
    ABSTRACT In modern technology, wireless communication is widespread and it started to be used in everyday life, for example, Wireless phone chargers, home automation systems, etc. widely use wireless communication. People want smart systems to make their life easy, and I want to discard the cables that limit our mobility. The purpose of this... Continue Reading
    Call Us Get this work