Chemical Engineering Project Topics with Materials:

ABSTRACT This project was done to extract and characterize bean oil according to their particle sizes. The experiment was carried out using scent bean (i.e. ‘Ozaki’, ‘Ijilizi’or ‘Azamu’) as sample. The oils were extracted by solvent extraction /leaching extraction using n-hexane. Proximate analysis was carried out to obtain percentage... Continue Reading

ABSTRACT This study is a comparative analysis of the use of coal, fuel oil and natural gas for cement production noting their physical and chemical properties, cost and availability, impact on the environment and human health. Out of the seven cement manufacturing industries in Nigeria, three industries use these fuels were selected for the study.... Continue Reading

ABSTRACT Activated carbon, also widely known as activated charcoal or activated coal is a form of carbon which has been processed to make it extremely porous and thus to have a very large surface area available for adsorption or chemical reactions (Mattson et al., 1971). The word active is sometimes used in place of activated. It is characterized... Continue Reading

ABSTRACT Biomass, particularly agricultural residues seem to be one of the most promising energy resources for developing countries (Patomsok, 2008). Rural households and minority of urban dwellers depend solely on fuel woods (charcoal, firewood and sawdust) as their primary sources of energy for the past decades (Onuegbu, 2010). Of all the... Continue Reading

ABSTRACT The research project studies the analysis of pear and its oil. The mesocarp from edible African pear “DacryodesEdulis” were evaluated for their oil yield. The pulp from this pear were oven dried at 100oC-105oC to a moisture content level of 29%.The mesocarp was subjected to proximate analysis to determine the percentage of the... Continue Reading

ABSTRACT Air pollutions pollutant showed that the extent of spreading depends on the motor vehicle traffic population of the area. This pollution strongly generated through combustion of fossil fuels presents difficult environmental challenge to societies as it could degrade the environment and affect human health and quality of life. Vehicular... Continue Reading

ABSTRACT This research work show cases the potentials of Itakpe Iron concentrate for Magneto-rhelogical abilities. The concentrate was first ball milled to size reduce it then subjected to low magnetic strength from magnetic bits in-situ the magnetic fluid. It was determined that temperature affected the fluid inversely, as temperature increased... Continue Reading

Azeotropic distillation of ethanol-water mixture is accomplished by adding a volatile third component to the liquid which changes the volatility of one of the two components more than the other so the components are separated by distillation. The two components to be separated often have similar boiling point components which do or do not... Continue Reading

Briquette is a block of compressed materials suitable for burning. Briquettes can be made from low cost materials such as old newspaper, any bio mass wastes and agricultural residues. They can be used as fuel instead of charcoal, firewood or mineral coal and costs less. Depending on which materials were used to make the briquettes, they may burn... Continue Reading

ABSTRACT The objective of the work is the catalytic conversion of waste plastics into fuel oil and solid wax using Ca(OH)2 and the design of pyrolysis reactor. Plastic wastes such as, polypropylene, low density polyethylene, high density polyethylene, polystyrene are the most frequently used in everyday activities and disposed of to the... Continue Reading

ABSTRACT Oil obtained from orange peels and velvet tamarind nut by solvent extraction (n-hexane and acetone) using the soxhlet extractor were investigated as feedstock’s to determine some of the suitable parameters such as iodine value, saponification value, specific gravity, density, acid value and free fatty acid value, and their percentage... Continue Reading

ABSTRACT Blender is an electric machine for size reducing soft food or liquid mixture. Blender is some time called liquidizer consists of a glass jar or jug containing a steel blade assembly at the base driven by a small electric motor. Construction of blender was done based on the principle of size of reduction using electric motor as the major... Continue Reading

ABSTRACT In the construct of 2,000 litres capacity water reservoir galvanized steel sheet forms the tank and an angle iron rod forms the stand. Two full length galvanized sheet were marked out and cut out to the required sizes. The work stated by cutting the it gauges galvanized steel sheets of full length into geometrical dimensions of the... Continue Reading

ABSTRACT The project Analysis of Enugu Coal was done to determine the characteristic properties of Enugu Coal with particular emphasis on the proximate and ultimate analysis. Coal samples from the Enugu Coal (Onyeama) mine were obtained and pulverized. The coal sample (pulverized) was subjected to proximate and ultimate analysis to determine its... Continue Reading

ABSTRACT This study has its theme as a utilization studies of Enugu coals with the view of studying its properties, classification, preparation storage etc comparing coals obtained from different locations. The Enugu coal is a sub-bitummous and non coking coal. It is very rich in waxes and resins, thus it may be suitable for the production of... Continue Reading

ABSTRACT This project “production of plane mirror using local raw material” is meant to study the possibility of producing plane mirror using sand rich in silica as its major local raw material. Plane mirror is produced by casting one side of a sheet glass. Presently in Nigeria, sheet glass is not used easily produce and as such, the... Continue Reading

ABSTRACT The refurbishment of the fluid flow demonstration unit was carried out in the Chemical Engineering pilot plant laboratory of the Institute of Management and Technology Enugu. The refurbishment process was carried out to ensure adequate functioning of the unit, to allow the continuous use of equipment in the pilot plant, so that student... Continue Reading

ABSTRACT This project was carried out using coal sample from Onyeama coal mine Enugu, Enugu State.Activated coal was produced by carbonizing the coal and activating it using phosphoric acid at a temperature of 5500c. the degree of bleaching of raw palm oil was monitored using spectronic meter through absorbance measurement. The essence was to... Continue Reading

ABSTRACT The repair of the fixed bed adsorption column, a product of arm field technical company was carried out for the purpose of bringing the faulty equipment back to its normal operating system. Before this exercise, the equipment was out of operation because of the completely blocked base of the fixed bed column (water column) and the... Continue Reading

ABSTRACT The project aims to develop a flow process to obtain the optimum temperature and time necessary for the maximum recovery of alkali present in palm inflorescence. On this ground, a preliminary experiment was performed. During this process, both male and female palm inflorescence were compared for maximum alkali production and it was... Continue Reading

ABSTRACT The need for an authentic and reliable report relating to the modification of a proto-type air-conditioning unit is inevitable. Many homes and offices use the air conditioner to cool the temperature in their respective homes and offices, so the maintenance of the air conditioner should be a top priority of every individual in order to... Continue Reading

ABSTRACT The production of the soap was carried out using all the necessary equipments like the reactor, mould, stirrer, hygrometer guage etc. and all the required reagents for soap production in correct proportion. In the production, palm kernel oil (P.K.O) was used instead of tallow or grease. This was because soap produced from grease or tallow... Continue Reading

ABSTRACT The candle mould has twenty four (24) holes which could produce twenty four (24) quality candle sticks Aluminum, a non ferrous metal was used as the construction material for the mould the type of casting technique used was green sand mould method. In the process of moulding the pattern was placed in the flask which contained the green... Continue Reading

ABSTRACT Interface on petroleum product in multi-purpose pipeline system refers to as the zone of demarcation between two products where mixing occurs.  Generally, interface is a boundary layer, so the boundary between two products when they are pumped in succession is known as interface. In Nigeria Petroleum Industries like NNPC (PPMC) make use... Continue Reading

ABSTRACT The aim of this project was to construct one office table and four chairs. In the course of this project the length of plank used was 12” and we used about 4 number (mahogany) of 1” thickness, ¾ plywood of 1 sheet of 1” thickness, as well as ¼” plywood of ½ and glue 1 tin wenner 1 rod, foam ½ sheet.... Continue Reading