Electrical Engineering Project Topics with Materials:

INTRODUCTION As the world is developing the need for electronics in human endeavor is now taking a larger scope. With the invention of certain electronics gadgets in our societies today, certain activities become easily handled for example; in communication where the telephone plays a part. In places where safety are needed an alarm system will be... Continue Reading

ABSTRACT In the world today, the use of power supply in electronics equipment and gadgets has increased and it is still increasing. These power supplies are not stable as required by these electronics. This arise the need for the power stabilization as to overcome this problem This project handles this problem very well. Some recommendations were... Continue Reading

The household lighting cost accounts for 10% of the electric bill, changing the light bulbs effectively can reduce the long term energy costs significantly. In Nigeria, where less than one percent of the population has access to 24 hours of interrupted power supply there is a need for a complementary, renewable source of light which provides... Continue Reading

Abstract A smoke detector is a device that senses smoke typically as an indicator of fire or non- smoking zone.  In order to ensure human safety and safeguard property against fire in both domestic and commercial settings, different solutions for smoke detection have been developed, a comprehensive literature was carried out on smoke detector,... Continue Reading

ABSTRACT In our present society, wireless communication has become most prevalent and mobile units (hand held devices /GSM/ Computers) are one of the most common equipments for conveying messages wirelessly. Owing to the fact that most youths in our society today on the average make use of at least one wireless device that communicate with other... Continue Reading

Abstract This project work was embarked on the construction and determination of the efficiency of 12 volts DC fan using two N3055 transistor, 1kΩ variable resistors, resistors, breadboard, veroboard, 12 volts DC battery and connectors at Science Laboratory Technological Department, Federal Polytechnic Offa, Nigeria. This is always required to... Continue Reading

The aim of this project is to shows the possibility of wireless power transfer through the design of a wireless charging pad.  In this project write-up, the methodology and principle of operation is wireless power transfer through inductive couple, a feasible design is modelled accordingly. The inductive couple technique is used because it is the... Continue Reading

Test and measuringinstruments are an indispensable in any electronics research, development ordesign environment. Test and measuring instruments can be categorized asdigital and analog. Analog systems change their signal output linearly with the input and can be represented on a scale by means of a pointer. In the other hand, digital instruments... Continue Reading

ABSTRACT Microcontroller has actually revolutionized the world economy as virtually every facet of life is benefiting in one way or the other on the great impact of Microcontroller today.Meanwhile,the technology of Microcontroller has gone long way of which monitoring and interfacing of real world devices to Microcontroller systems can not be left... Continue Reading

ABSTRACT The world today is moving ahead at a very fast pace. Some of the very common examples of fast moving objects are aeroplanes, high speed cars and many more. In our everyday life we come across many fast moving vehicles and so it is very important to measure the speed of these vehicles.This is an era of automation where it is broadly... Continue Reading

ABSTRACT This design is aimed at providing a system that has the capability of recharging batteries after use. The design is to incorporate an auto charging cut off circuit that operates when the battery is fully charged to avoid damaging the device and also a low voltage circuit which prevents the system from damage should in case the battery... Continue Reading

ABSTRACT This system “” comprises of many modules which are: The Sensor/Input Unit, Microcontroller Unit and the Output Interface. The sensor detects when the hand approaches the nozzle. Once the approaching hand is detected, the hand dryer produces a very hot to dry the hand as well as... Continue Reading

INTRODUCTION This project presents the design and construction of a computer based program used to control office appliance. It is based on a Graphic user interface (GUI) programming language (Visual Basic 6.0), Parallel Port Interactive Mode, Opto-Coupler Isolation of the computer from the appliance to prevent damage to the system should a fault... Continue Reading

This work is based on automatic changeover switch. If there is failure in main power supply it will automatically change to auxiliary power supply such as generator. This project is based on electromechanical changeover with the use of magnetic contractors, relay,and circuit breaker.... Continue Reading

ABSTRACT This project involves the development of a console that allows multiple inputs (3 inputs) and a single output to a screen through the use of software. The micro controller which serves as the ‘heart’ of the hardware was encoded using C programming language. These lines of code enable the micro controller to switch to the selected... Continue Reading

ABSTRACT The motive of this project is to construct equipment for deodorizing kerosene, hence the smell of kerosene is totally eradicated. The equipment was constructed with flat sheet plates of a desired standard, the dimension and the truncated parts were coupled and welded in order to fasten the parts together. The material was selected to... Continue Reading

ABSTRACT The Orsat Gas Analyzer was constructed at the project development institute (PRODA), Enugu. The operation involved the laboratory glass blowing which entails the heating of a glass tube. The heating •continues until the glass tube reaches its plastic state. The shape of the tube is changed or the required shape blown by pulling, bending... Continue Reading

ABSTRACT Waste and residuals are undeniably part of the human society. The accumulation of these materials and the “throw away” philosophy results in many environmental and health issues and safety hazard problems prevent sustainable development in terms of resource recovery and recycling of waste materials. The carbon sources in the waste can... Continue Reading

ABSTRACT This project is titled the construction of a DC to AC inverter system. It is constructing to meet up with the power demand in the offices and in homes in the absence of power supply from the power holding company of Nigeria, PHCN. In order words the device / item serves as a substitute for PHCN which almost monopolises the power supply to... Continue Reading

Abstract Induction machine account for about 60percent of the electrical consumption in industrial countries; hence a huge energy savings could be achieved by even a small increment in the machine efficiency. Improving the designs of induction machines requires accurate quantification of the machine losses. A significant portion of the losses in... Continue Reading

The need for identification leads to the study of biometrics. Over the ages, human beings have been identified by various means, such as the Name, Complexion, Nationality, and even some uniquely assigned codes. Of all these methods, none can be used to uniquely identify an individual distinctly under all circumstances. However, research has shown... Continue Reading

ABSTRACT This write up is a detail of the process and information of plan for the physical realization of the construction of the 1M3 mobile deep freezer. It is divided into chapters, which discussed extensively the practical refrigeration cycle with full attention given to design factors working principle and choice of material. The method used... Continue Reading

Table of Contents 1. Introduction 2. Electricity Demand 3. Wind Power System 4. Floating Solar Photovoltaic (PV) System 5. Electricity Storage Systems ____ 6. Site Choice 7. Planning Permission Statement 8. Environmental Impact Assessment _ 9. Project Plan 10.... Continue Reading

Abstract This project work centered on construction of 12V/10A solar charge controller that is needed in photovoltaic system to safely charge regulate and discharge of sealed lead acid battery through DC load. Solar charge controller is devices that regulate solar photovoltaic power and prevent overcharging, over discharging or overflow of current... Continue Reading

ABSTRACT The Airbeetle-18 unmanned Aircraft is an Aircraft design for the purpose of surveillance following the fact that the parent Airbeetle-18 has almost reached the end of its life time. Hence, there is need to convert it to an unmanned aircraft in other to extend its service life time. A comprehensive literature review was carried out on... Continue Reading